Specs : Ultra High-Speed/High-Accuracy Laser Displacement Sensor - LK-G5000 series

Sensor heads: Diffuse reflection mode

Model		LK-H020	LK-H025	LK-H050	LK-H055	LK-H022	LK-H027	LK-H052	LK-H057
Image
Mounting mode		Diffuse reflective
Reference distance		20mm		50 mm		20mm		50 mm
Measuring range		±3 mm^*1		±10 mm^*1		±3 mm^*1		±10 mm^*1
Light source	Type	Red semiconductor laser
	Wavelength	655nm
	Laser class	IEC 60825-1: Class 3R FDA(CDRH)21CFR Part 1040.10: Class IIIa				IEC 60825-1: Class 2 FDA(CDRH)21CFR Part 1040.10: Class II
	Output	4.8mW				0.95mW
Spot diameter (at standard distance)		ø25 µm	25 µm x 1,400 µm	ø50 µm	50 µm x 2,000 µm	ø25 µm	25 µm x 1,400 µm	ø50 µm	50 µm x 2,000 µm
Linearity		±0.02% of F.S. (F.S.= 6 mm)^*2	±0.02%of F.S. (F.S.= 6 mm)^*2	±0.02% of F.S. (F.S.= 20 mm)^*2	±0.02% of F.S. (F.S.= 20 mm)^*2	±0.02% of F.S. (F.S.= 6 mm)^*2	±0.02%of F.S. (F.S.= 6 mm)^*2	±0.02% of F.S. (F.S.= 20 mm)^*2	±0.02% of F.S. (F.S.= 20 mm)^*2
Repeatability		0.02 µm (0.01 µm)^*3		0.025 µm^*3		0.02 µm (0.01 µm)^*3		0.025 µm^*3
Sampling cycle		2.55/5/10/20/50/100/200/500/1000 µs (9 steps selectable)
Temperature characteristics		0.01% of F.S./°C (F.S.= 6 mm)	0.01% of F.S./°C (F.S.= 6 mm)	0.01% of F.S./°C (F.S.= 20 mm)	0.01% of F.S./°C (F.S.= 20 mm)	0.01% of F.S./°C (F.S.= 6 mm)	0.01% of F.S./°C (F.S.= 6 mm)	0.01% of F.S./°C (F.S.= 20 mm)	0.01% of F.S./°C (F.S.= 20 mm)
Environmental resistance	Enclosure rating	IP67
	Ambient light	Incandescent lamp or fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +50 °C^*4	0 to +50 °C	0 to +50 °C^*4	0 to +50 °C	0 to +50 °C^*4	0 to +50 °C	0 to +50 °C^*4	0 to +50 °C
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions
Material		Aluminium die-cast
Weight		Approx. 230 g		Approx. 260 g		Approx. 230 g		Approx. 260 g
^1 Measurement range when the sampling cycle is 20 µs or more. ^2 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured in the normal measurement mode. ^3 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured at the reference distance with the number of averaging measurements set to 16384. The value in parentheses is a typical e x ample of a measurement with the number of averaging measurements set to 65536 and the sampling cycle to 200 µs. ^4 When the ambient temperature rises to 40 °C or more, mount this on a metal plate before use.

Back to top

Sensor heads: Diffuse reflection/Specular reflection mode

Model		LK-H080	LK-H085	LK-H150	LK-H155	LK-H082	LK-H087	LK-H152	LK-H157
Image
Mounting mode		Diffuse reflective				Diffuse reflective / Specular reflective^*5
Reference distance		80 mm		150 mm		Diffuse reflective: 80 mm Specular reflective: 76.7 mm		Diffuse reflective: 150 mm Specular reflective: 147.5 mm
Measuring range		±18 mm^*1		±40 mm^*1		Diffuse reflective: ±18 mm Specular reflective: -17.6 mm to +14.5 mm^*1		Diffuse reflective: ±40 mm Specular reflective: -39.5 mm to +24.4 mm^*1
Light source	Type	Red semiconductor laser
	Wavelength	655nm
	Laser class	IEC 60825-1: Class 3R FDA(CDRH)21CFR Part 1040.10: Class IIIa				IEC 60825-1: Class 2 FDA(CDRH)21CFR Part 1040.10: Class II
	Output	4.8mW				0.95mW
Spot diameter (at standard distance)		ø70 µm	70 µm x 2,500 µm	ø120 µm	120 µm x 4,200 µm	ø70 µm	70 µm x 2,500 µm	ø120 µm	120 µm x 4,200 µm
Linearity		±0.02% of F.S. (F.S.= 36 mm)^*2	±0.02% of F.S. (F.S.= 36 mm)^*2	±0.02% of F.S. (F.S.= 80 mm)^*2	±0.02% of F.S. (F.S.= 80 mm)^*2	±0.02% of F.S. (F.S.= 36 mm)^*2		±0.02% of F.S. (F.S.= 80 mm)^*2
Repeatability		0.1 µm^*3		0.25 µm^*3		0.1 µm^*3		0.25 µm^*3
Sampling cycle		2.55/5/10/20/50/100/200/500/1000 µs (9 steps selectable)
Temperature characteristics		0.01% of F.S./°C (F.S.= 36 mm)	0.01% of F.S./°C (F.S.= 36 mm)	0.01% of F.S./°C (F.S.= 80 mm)	0.01% of F.S./°C (F.S.= 80 mm)	0.01% of F.S./°C (F.S.= 36 mm)		0.01% of F.S./°C (F.S.= 80 mm)
Environmental resistance	Enclosure rating	IP67
	Ambient light	Incandescent lamp or fluorescent lamp: 10,000 lux max.						Incandescent lamp or fluorescent lamp: 5,000 lux max.
	Ambient temperature	0 to +50 °C^*4
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions
Material		Aluminium die-cast
Weight		Approx. 280 g		Approx. 300 g		Approx. 280 g		Approx. 300 g
^1 Measurement range when the sampling cycle is 20 µs or more. ^2 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured in the normal measurement mode. ^3 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured at the reference distance with the number of averaging measurements set to 16384. The value in parentheses is a typical e x ample of a measurement with the number of averaging measurements set to 65536 and the sampling cycle to 200 µs. ^4 When the ambient temperature rises to 40 °C or more, mount this on a metal plate before use. ^*5 Use one of the following dark filters when measuring a transparent or mirror surface object: LK-H082/LK-H087: LK-F3, LK-H152/LK-H157: LK-F2

Back to top

Sensor heads: Specular reflection mode

Model		LK-H008	LK-H008W	LK-H022K	LK-H027K	LK-H052K	LK-H057K
Image
Mounting mode		Specular reflective
Reference distance		8mm		16.1mm		46.3mm
Measuring range		±0,5 mm^*1	±0.5 mm^*1	±2.8 mm^*1		±5.2 mm^*1
Light source	Type	Red semiconductor laser
	Wavelength	655nm
	Laser class	IEC 60825-1: Class 1 FDA(CDRH)21CFR Part 1040.10: Class II		IEC 60825-1: Class 2 FDA(CDRH)21CFR Part 1040.10: Class II
	Output	0.3mW		0.95mW
Spot diameter (at standard distance)		ø20 µm	20 µm x 550 µm	ø25 µm	25 µm x 1,400 µm	ø50 µm	50 µm x 2,000 µm
Linearity		±0.05% of F.S. (F.S.= 1 mm)^*2		±0.02% of F.S. (F.S.= 6 mm)^*2		±0.02% of F.S. (F.S.= 20 mm)^*2
Repeatability		0.005 µm (0.001 µm)^*3		0.02 µm (0.01 µm)^*3		0.025 µm^*3
Sampling cycle		2.55/5/10/20/50/100/200/500/1000 µs (9 steps selectable)
Temperature characteristics		0.02% of F.S./°C (F.S.=1 mm)		0.01% of F.S./°C (F.S.= 6 mm)		0.01% of F.S. (F.S.= 20 mm)
Environmental resistance	Enclosure rating	IP67
	Ambient light	Incandescent lamp or fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +50 °C^*4		0 to +50 °C
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions
Material		Aluminium die-cast
Weight		Approx. 240 g		Approx. 230 g		Approx. 260 g
^1 Measurement range when the sampling cycle is 20 µs or more. ^2 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured in the normal measurement mode. ^3 This value is obtained when the KEYENCE standard target (White diffuse workpiece or workpiece with a metal mirror surface only for the LK-H008/LK-H008W) is measured at the reference distance with the number of averaging measurements set to 16384. The value in parentheses is a typical e x ample of a measurement with the number of averaging measurements set to 65536 and the sampling cycle to 200 µs. ^4 When the ambient temperature rises to 40 °C or more, mount this on a metal plate before use.

Back to top

Main unit

Model		LK-G5001V^1^2	LK-G5001PV^8^2
Image
Separate type		LK-G5001/LK-HD500	LK-G5001P/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx. 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analogue output voltage	±10 V output, Output impedance: 100 Ω
	Analogue current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analogue outputs	2
	TIMING 1 input	Non-voltage input^*3	Voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Non-voltage input^*4	Voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	NPN open-collector output	PNP open-collector output
	General comparator output
Expansion connector	TIMING input	Non-voltage input	Voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output	PNP open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C. When two or more head expansion units are connected: 0 to +40 °C.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 1/2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office. ^8 PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA

Back to top

Head expansion unit

Model		LK-HA100
Image
Separate type		LK-HA100
Type		Head expansion unit
Sensor head compatibility		Compatible
No. of connectable sensor heads		1
Display interface	LED indicator	POWER ON, STABILITY, BRIGHT, DARK
Terminal block	Analogue output voltage	±10 V output, Output impedance: 100 Ω
	Analogue current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analogue outputs	1
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Power supply	Power supply voltage	24 VDC ±10 % (Supplied from the controller)
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C. When two or more head expansion units are connected: 0 to +40 °C.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 300 g

Back to top

LK-G5000 Series Touch Panel Display

Model		LK-HD1001
Image
Type		LK-G5000 Series Touch Panel Display
Display panel	Display colour	TFT colour LCD
		32,768 colours
	Pixels	W 640 × H 480 pixels
	Display area	W 170.9 × H 128.2 mm
Displaypanel	Service life (normal temperature andhumidity)	Approx 50,000 hours
Backlight	Method	White LED
	Duration	Approx 50,000 hours
Touch switch	Number of switches	40 × 30 per 1 image
Touchswitch	Method	Matrix resistance membrane mode
	Operating force	0.98N or less
	Life-span	More than one million times
Communication feature		Available only with the LK-G5000 Series
Structure		Panel built-in type, IP65f equivalent dust-proof, waterjet-proof on only front panel
Power supply	Power supply voltage	24 VDC ±10%
	Maximum current consumption	1 A or less
Environmental resistance	Ambient temperature	0 to +50 °C
	Relative humidity	35 to 85 % RH (No condensation)^*1
	Storage temperature	-10 to +60 °C (No freezing)
	Storage relative humidity	35 to 85 % RH (No condensation)^*2
	Operating environment	No dust or corrosive gas
	Vibration resistance	10 to 57 Hz, Double amplitude 0.3 mm, 57 to 500 Hz, 2 G for 3 hours in each of the X, Y, and Z directions
Weight		Approx. 1,150 g
^1 When the ambient temperature is higher than +40 °C, limit the absolute humidity to 85 % RH at +40 °C. ^2 When the ambient temperature is higher than 40 °C, limit the absolute humidity to 85 % RH at 40 °C.

Back to top

Sensor head-to-controller cable

Model	CB-A07	CB-A2	CB-A5	CB-A10	CB-A20	CB-A30
Image
Length	0.7 m	2 m	5 m	10 m	20 m	30 m
Weight	Approx. 100 g	Approx. 200 g	Approx. 400 g	Approx. 550 g	Approx. 1,400 g	Approx. 2,000 g

Back to top

Sensor head-to-controller extension cable

Model	CB-A5E	CB-A10E
Image
Length	5 m	10 m
Weight	Approx. 400 g	Approx. 750 g

Back to top

CC-Link unit

Model		LK-CC100
Image
Type		CC-Link communication unit dedicated to LK-G5000 Series
Network connection	Supported CCLink version	Ver. 1.10 (Extended cyclic setting: Single) Ver. 2.00 (Extended cyclic setting: Double or more)^1^2
	Master unit	CLPA-certified master unit (CC-Link Ver. 2.00/Ver. 1.10)
	No. of occupied stations	1 to 4
	Communication speed	156kbps、625kbps、2.5Mbps、5Mbps、10Mbps
	Connection cable	Dedicated CC-Link cable supporting Ver. 1.10 (Shielded 3-core twisted-pair cable: OP-79426, OP-79427)
	Maximum total cable extension length	156kbps…1200m、 625kbps…900m、 2.5Mbps…400m、 5Mbps…160m、 10Mbps…100m
	Station type	Remote device station
Power supply	Power supply voltage	24 VDC ±10 % (supplied from controller)
	Maximum current consumption	200mA or less
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C. When two or more head expansion units are connected: 0 to +40 °C.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 300 g
^1 The LK-G5000 Series supports the "extended cyclic transmission" and "station-to-station cable length relaxation" of CC-Link Ver. 2.00. ^2 CC-Link is a registered trademark of Mitsubishi Electric Corporation.

Back to top

DeviceNet unit

Model		LK-DN100
Image
Type		DeviceNet® communication unit dedicated to LK-G5000 Series
Network connection	Master unit	ODVA-certified master unit
	Maximum trunk line cable length	Thick cable: 500 m (at transmission speed of 125 kbps)/250 m (at 250 kbps)/ 125 m (at 500 kbps) Thin cable: 100 m (at all transmission speed settings)
	Communication protocol	DeviceNet®^*1 compliant
	Transmission speed	500 kbps, 250 kbps, 125 kbps
	Device type	Generic
	Transmission medium	Dedicated 5 cables (2 signal cables, 2 power supply cables, 1 shielding cable)
	Communication type	I/O communication (Poll) Explicit message communication
	Power supply	11 to 25 VDC
	Current consumption	10 mA max. (when network power supply 24 V is applied)
Power supply	Power supply voltage	24 VDC ±10% (supplied from controller)
	Maximum current consumption	200mA or less
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C. When two or more head expansion units are connected: 0 to +40 °C.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 300 g
^*1 DeviceNet® is a registered trademark of ODVA (Open DeviceNet® Vendor Association).

Back to top

Specs Ultra High-Speed/High-Accuracy Laser Displacement Sensor LK-G5000 series

Sensor heads: Diffuse reflection mode

Sensor heads: Diffuse reflection/Specular reflection mode

Sensor heads: Specular reflection mode

Main unit

Head expansion unit

LK-G5000 Series Touch Panel Display

Sensor head-to-controller cable

Sensor head-to-controller extension cable

CC-Link unit

DeviceNet unit